Shaping a Stronger Bracket
The intense heat and vibration in an engine compartment of an automobile can easily cause part failure. Kyungshin Corp. turned to topology optimization using ANSYS Mechanical to design stiffer, lighter brackets to support their smart junction blocks and reduce risk. Topology optimization cut development time in half while increasing the lifetime of the bracket and minimizing material costs.
Three Steps to Success
In the first step of the design process, Kyungshin engineers defined the load conditions experienced by the bracket in normal operation, established the allowable range of design parameters and generated an initial design based on the density distribution of the bracket using topology optimization. The bracket size was limited to the available space in the engine compartment that would not interfere with any nearby component. Engineers defined the vibration simulation conditions of the bracket by stipulating fixed points in the design and the acceleration load (4.5 G) experienced due to vibration. They then used topology optimization to generate an initial bracket layout using density distribution analysis. They explored brackets with density distributions of 20, 50 and 80 percent, and verified a bracket shape in each case that would provide the desired stiffness.
The second step involved shape optimization of the bracket based on the 50 percent density distribution model developed in the first step. Kyungshin engineers generated a parametric model with minimum and maximum dimensions for each defined design factor, including right and left side bracket width, height, angle and center radius. They then performed design of experiments (DoE) simulations automatically using ANSYS DesignXplorer. Employing the manual central composite design (CCD) algorithm in ANSYS optiSLang they obtained an optimal value for each parameter that resulted in a bracket with reduced mass and increased stiffness compared to the original bracket they were trying to replace.
Picture 1 Original model – Picture 2 Optimale model
A smart junction block is the central nervous system of an automobile. The PCB of the junction box manages the electricity and distributes power to all parts of the vehicle, so it is a critical component of the modern car. Because of the vibration and high temperatures in the engine compartment, the junction block and the bracket that connects it to the chassis must be designed with high stiffness to resist cracking and vibration fatigue. Traditionally, the bracket was designed using a build-and-test method, which was slow and costly. Also, engineers tended to use more material than was necessary to ensure high stiffness, which raised the cost of raw materials.
To avoid such over-design problems and develop plastic junction block brackets with optimal dimensions to maintain the necessary stiffness, Kyungshin engineers used the topology optimization functionality of ANSYS Mechanical to design durable, lightweight brackets. With topology optimization, the simulation software automatically determines the best shape once engineers specify where supports and loads are located on a volume of material. For example, instead of a continuous solid bracket, topology optimization might find that a lightweight design with ribs and void spaces produces a bracket that meets all mechanical requirements. In this case, ANSYS Mechanical’s topology optimization capability performed digital exploration to determine the optimal bracket shape, rib shape and rib positions.
Finally, the engineers verified the performance of the proposed optimal bracket using vibration fatigue simulation. The simulation involved varying the vibration acceleration from 4.5 G to 3.0 G over three minutes while the vibration frequency varied from 20–50 Hz (at 4.5 G) to 50–200 Hz (at 3.0 G). The simulation also cycled the temperature from 90 C to –30 C back to 90 C over a 24-hour period to ensure that the bracket could withstand the temperature variations inside the engine compartment.
“Topology optimization ensures cost savings through designs that use the minimum amount of material necessary to meet required mechanical standards while increasing product lifetime.”
A Better Bracket
The vibration fatigue simulations revealed that the optimal model had a breakage lifetime of 2,259 operating hours versus 1,544 hours for the original bracket model. This is an increase in product lifetime of 46 percent — a significant improvement. The new bracket also was lighter, using 16 percent less plastic than the original, continuous solid bracket. In the process, Kyungshin engineers reduced the development period for the new bracket from six months to three months, greatly decreasing development costs. They also created a new thermal– vibration–fatigue simulation process using ANSYS Mechanical running on ANSYS Workbench to forecast the breakdown of the junction block bracket, which can be used in preventive maintenance scheduling.
By substituting simulation for traditional methods that relied on an engineer’s experience and existing design standards, Kyungshin engineers have cut in half the number of bracket performance verification analyses, from eight to four. At a cost of approximately 50 million to 100 million won (US$45,000 to $90,000) per verification analysis, this is a major savings. In addition, they have produced a reusable model on which to base all future junction block bracket designs. The new model, employing ANSYS topology optimization, offers a flexible design scheme that the engineers can modify for any other component they may decide to manufacture in the future. Topology optimization ensures cost savings through designs that use the minimum amount of material necessary to meet required mechanical standards while increasing product lifetime.
Read the article here! (pdf-file)
By Kim Byeongwoo, Design Team Manager, Kyungshin, Incheon, Korea
Follow us — Connect with EDRMedeso on social media